3D printer electricity cost

The number on the power supply is a peak capacity, not what the printer uses. Measure average watts, then multiply by your real price per kilowatt-hour.

In short: Use average print watts, not the PSU label. At the site’s Israeli default of ₪0.635/kWh incl. VAT (1 July 2026), 5 hours cost about ₪0.25 on an A1 mini (80 W, official Bambu wiki) and about ₪0.79 on an X2D (250 W official steady-state PLA). An AMS 2 Pro drying heater is 80 W while drying only, from the same official wiki, and is not included in the print average.

The formula

kWh used = (average watts / 1000) × print hours
electricity cost = kWh used × price per kWh

A 120 W average over 5 hours is 0.60 kWh. At $0.18 per kWh that is about $0.11. At Israel’s mid-2026 household rate of about ₪0.635 per kWh (including VAT), the same job is about ₪0.38. Electricity is often a small share of a desktop print’s cost, but it is the line people most often guess wrong, because they start from the wrong wattage.

Do not use the power-supply rating

A “360 W” or “700 W” label on the brick or the PSU is how much the supply can deliver, not how much the printer draws while printing. During heat-up the bed and nozzle can pull a large share of that capacity for a few minutes. Once they are at temperature, thermostats cycle the heaters on and off. Over a multi-hour PLA print, average power is typically far lower than the label.

Average draw still moves around. A larger bed, a higher bed temperature (ABS, ASA, nylon, polycarbonate), an actively heated enclosure, and a second nozzle all push the average up. A short, cool PLA job on a small open-frame machine sits at the low end. Published meter tests of common FDM printers often land somewhere in the tens to low hundreds of watts on average for everyday PLA; treat that only as a starting range and measure your own machine.

How to measure average watts

  1. Plug the printer into a simple energy meter or a smart plug that reports kilowatt-hours. Reset the energy counter, or note the reading.
  2. Run a representative print — the same material, bed temperature and enclosure setup you usually use. A 20-minute benchy understates heat-up’s share; a job of a few hours is better.
  3. When the print ends, read kWh and divide by hours, then multiply by 1,000:
average watts = (kWh / hours) × 1000

Example: the meter shows 0.48 kWh after 4.0 hours. Average power is (0.48 / 4) × 1000 = 120 W. Put 120 in the calculator, not the PSU’s 360 W. If you print both cool PLA and hot engineering materials, keep two averages.

A tagged link to a plug-in energy meter will go here after the site owner’s Amazon Associates account is approved. Do not invent an associate tag.

What to enter for the kWh price

Use the all-in price on your bill — energy, delivery, and taxes — because that is what you actually pay. If you are on a time-of-use plan, use the rate that applies when the printer usually runs (often overnight). The calculator ships with national-average defaults so first-time users see a plausible number. They are not your rate.

RegionDefault in the calculatorWhat it is based on
United States (USD) $0.18 / kWh U.S. Energy Information Administration figures for residential electricity in 2026 have been around 18 cents per kWh (about 18.16¢ in August 2026 in EIA’s Electric Power Monthly / related summaries). Your state can be much lower or higher.
European Union (EUR) €0.28 / kWh Eurostat reported an EU household average of €0.28 per kWh in the first half of 2026, down slightly from €0.29 in the second half of 2025. National prices ranged from about €0.11 (Hungary) to €0.39 (Ireland).
Israel (ILS) ₪0.635 / kWh The uniform residential consumption tariff as of 1 July 2026 is commonly cited as 53.83 agorot/kWh before VAT and 63.52 agorot/kWh including 18% VAT (0.6352 shekels), based on the Israel Public Utilities Authority tariff updates. GlobalPetrolPrices separately listed a March 2026 residential price of ILS 0.666 / kWh. Use the line on your IEC or supplier bill, including VAT.

Sources: EIA Electric Power Monthly; Eurostat news article, 30 October 2026; Israel tariff figures compiled from the PUA tariff book / Decision 72806 as summarized by independent explainers such as SUNCAL’s 2026 tariff page, and GlobalPetrolPrices, Israel, March 2026. Always prefer your own bill.

A quick check

If electricity ever looks huge in the calculator, you probably entered nameplate watts or a price per kWh with the decimal in the wrong place (for example 18 instead of 0.18, or 63 instead of 0.635). If it looks tiny, that can still be right — many small PLA parts cost cents, not dollars, to power.

Back to the calculator · Full cost method

Frequently asked questions

How much electricity is 5 hours on an X2D?

1.25 kWh × ₪0.635 ≈ ₪0.79, using the official 250 W PLA steady-state figure and the site’s Israeli default tariff.

Is drying included?

No. Bambu lists AMS 2 Pro drying at 80 W during drying only. Add that separately if the dryer is running.